Compact Laser Diode Modules
- Max Power Ranging from 4.0 to 20 mW
- Six Versions with Wavelengths Ranging from 405 to 1550 nm
- SM1-Threaded for Lens Tube Compatibility
785 nm, 20 mW
|LDM405||405 nm||3.0 mm x 5.0 mm||4.0 mW||3R|
|LDM635||635 nm||3.0 mm x 5.0 mm||4.0 mW||3R|
|LDM670||670 nm||2.2 mm x 4.4 mm||5.5 mW||3B|
|LDM785||785 nm||2.6 mm x 4.4 mm||20 mW||3B|
|LDM850||850 nm||3.5 mm x 4.4 mm||20 mW||3B|
|LDM1550||1550 nm||2.6 mm x 3.0 mm||4.5 mW||1|
- Adjustable Output Power
- Collimated Output Beam
- Integrated Beam Shutter
- Internal SM1 (1.035"-40) Threads
- IEC60825-1/CDRH Compliant
- Power Supply Included
The LDM Series of compact laser sources are well suited to benchtop optical experiments. They are available at six wavelengths: 405 nm, 635 nm, 670 nm, 785 nm, 850 nm, and 1550 nm.
The Ø1.40" by 5.8" housing contains a Fabry-Perot laser diode with a bandwidth typically around 1 nm, collimating lens, and power controller. Each laser diode module includes a built-in shutter and internal SM1 (1.035"-40) threads for mounting with an extensive range of optomechanical devices from lens tubes to lens mounts. These laser modules are typically used as alignment aids within an SM1 Lens Tube system, as shown in the figure below to the left.
The LDM modules can be mounted to any optical table using one of our C1512(/M), C1513(/M), KM200V(/M), or VC3C(/M) V-groove mounts. Besides the mechanical shutter, the module also features a remote interlock connection and key-lock power switch. The laser module has an enable/disable toggle switch, laser on indicator LED, and top-located power adjustment pot controller.
The power can be adjusted from 0 to full power by adjusting a pot, as shown in the image at the bottom right. The output of each laser diode is polarized and multi-longitudinal mode. When the Laser Enable button is facing up, the light will be vertically polarized, with the exception of the LDM635, which will have horizontal polarization. Each LDM comes with a universal power supply.
Key-Lock, Power Port, and Interlock with Shorting Pin
|Wavelength, Typical||405 nm||635 nm||670 nm||785 nm||850 nm||1550 nm|
|Wavelength, Min/Max||395 - 415 nm||625 - 645 nm||660 - 678 nm||776 - 800 nm||840 - 860 nm||1520 - 1580 nm|
|Beam Size (Elliptical)a||3.0 mm x 5.0 mm||3.0 mm x 5.0 mm||2.2 mm x 4.4 mm||2.6 mm x 4.4 mm||3.5 mm x 4.4 mm||2.6 mm x 3.0 mm|
|Output Powerb||4.0 mW||4.0 mW||5.5 mW||20 mW||20 mW||4.5 mW|
|Stability, Short Term (30 min)||0.01 dB|
|Stability, Long-Term Drift (24 hr)||0.1 dB|
|Operating Temperature||10 - 40 °C|
|Storage Temperature||5 - 50 °C|
|Power Supply (Included)||Input: 100 - 240 VAC, 0.48 A
50 - 60 Hz
Output: 9 VDC @ 2.2 A
Laser Safety and Classification
Safe practices and proper usage of safety equipment should be taken into consideration when operating lasers. The eye is susceptible to injury, even from very low levels of laser light. Thorlabs offers a range of laser safety accessories that can be used to reduce the risk of accidents or injuries. Laser emission in the visible and near infrared spectral ranges has the greatest potential for retinal injury, as the cornea and lens are transparent to those wavelengths, and the lens can focus the laser energy onto the retina.
Safe Practices and Light Safety Accessories
- Laser safety eyewear must be worn whenever working with Class 3 or 4 lasers.
- Regardless of laser class, Thorlabs recommends the use of laser safety eyewear whenever working with laser beams with non-negligible powers, since metallic tools such as screwdrivers can accidentally redirect a beam.
- Laser goggles designed for specific wavelengths should be clearly available near laser setups to protect the wearer from unintentional laser reflections.
- Goggles are marked with the wavelength range over which protection is afforded and the minimum optical density within that range.
- Laser Safety Curtains and Laser Safety Fabric shield other parts of the lab from high energy lasers.
- Blackout Materials can prevent direct or reflected light from leaving the experimental setup area.
- Thorlabs' Enclosure Systems can be used to contain optical setups to isolate or minimize laser hazards.
- A fiber-pigtailed laser should always be turned off before connecting it to or disconnecting it from another fiber, especially when the laser is at power levels above 10 mW.
- All beams should be terminated at the edge of the table, and laboratory doors should be closed whenever a laser is in use.
- Do not place laser beams at eye level.
- Carry out experiments on an optical table such that all laser beams travel horizontally.
- Remove unnecessary reflective items such as reflective jewelry (e.g., rings, watches, etc.) while working near the beam path.
- Be aware that lenses and other optical devices may reflect a portion of the incident beam from the front or rear surface.
- Operate a laser at the minimum power necessary for any operation.
- If possible, reduce the output power of a laser during alignment procedures.
- Use beam shutters and filters to reduce the beam power.
- Post appropriate warning signs or labels near laser setups or rooms.
- Use a laser sign with a lightbox if operating Class 3R or 4 lasers (i.e., lasers requiring the use of a safety interlock).
- Do not use Laser Viewing Cards in place of a proper Beam Trap.
Lasers are categorized into different classes according to their ability to cause eye and other damage. The International Electrotechnical Commission (IEC) is a global organization that prepares and publishes international standards for all electrical, electronic, and related technologies. The IEC document 60825-1 outlines the safety of laser products. A description of each class of laser is given below:
|1||This class of laser is safe under all conditions of normal use, including use with optical instruments for intrabeam viewing. Lasers in this class do not emit radiation at levels that may cause injury during normal operation, and therefore the maximum permissible exposure (MPE) cannot be exceeded. Class 1 lasers can also include enclosed, high-power lasers where exposure to the radiation is not possible without opening or shutting down the laser.|
|1M||Class 1M lasers are safe except when used in conjunction with optical components such as telescopes and microscopes. Lasers belonging to this class emit large-diameter or divergent beams, and the MPE cannot normally be exceeded unless focusing or imaging optics are used to narrow the beam. However, if the beam is refocused, the hazard may be increased and the class may be changed accordingly.|
|2||Class 2 lasers, which are limited to 1 mW of visible continuous-wave radiation, are safe because the blink reflex will limit the exposure in the eye to 0.25 seconds. This category only applies to visible radiation (400 - 700 nm).|
|2M||Because of the blink reflex, this class of laser is classified as safe as long as the beam is not viewed through optical instruments. This laser class also applies to larger-diameter or diverging laser beams.|
|3R||Class 3R lasers produce visible and invisible light that is hazardous under direct and specular-reflection viewing conditions. Eye injuries may occur if you directly view the beam, especially when using optical instruments. Lasers in this class are considered safe as long as they are handled with restricted beam viewing. The MPE can be exceeded with this class of laser; however, this presents a low risk level to injury. Visible, continuous-wave lasers in this class are limited to 5 mW of output power.|
|3B||Class 3B lasers are hazardous to the eye if exposed directly. Diffuse reflections are usually not harmful, but may be when using higher-power Class 3B lasers. Safe handling of devices in this class includes wearing protective eyewear where direct viewing of the laser beam may occur. Lasers of this class must be equipped with a key switch and a safety interlock; moreover, laser safety signs should be used, such that the laser cannot be used without the safety light turning on. Laser products with power output near the upper range of Class 3B may also cause skin burns.|
|4||This class of laser may cause damage to the skin, and also to the eye, even from the viewing of diffuse reflections. These hazards may also apply to indirect or non-specular reflections of the beam, even from apparently matte surfaces. Great care must be taken when handling these lasers. They also represent a fire risk, because they may ignite combustible material. Class 4 lasers must be equipped with a key switch and a safety interlock.|
|All class 2 lasers (and higher) must display, in addition to the corresponding sign above, this triangular warning sign.|
Click to Enlarge
|Item #||% Weight
- Reduce Weight of Packaging Materials
- Increase Usage of Recyclable Packing Materials
- Improve Packing Integrity
- Decrease Shipping Costs
Thorlabs' Smart Pack Initiative is aimed at waste minimization while still maintaining adequate protection for our products. By eliminating any unnecessary packaging, implementing packaging design changes, and utilizing eco-friendly packaging materials for our customers when possible, this initiative seeks to improve the environmental impact of our product packaging. Products listed above are now shipped in re-engineered packaging that minimizes the weight and the use of non-recyclable materials.b As we move through our product line, we will indicate re-engineered packages with our Smart Pack logo.