Narrow-Linewidth Single-Frequency Laser System, 1550 nm


  • 100 Hz Linewidth (Lorentzian) with 70 dB Typical SMSR
  • Relative Intensity Noise (RIN) of -160 dBc/Hz
  • Typical Output Power of 120 mW
  • 20 MHz Current Modulation Bandwidth

ULN15TK

Turnkey Ultra-Low-Noise Laser, 1550 nm

Typical frequency noise for the ULN15TK laser. See the Graphs tab for additional performance plots.

US Patents: 10193306, 10483718,
10476233, and 10454248

Related Items


Please Wait
Key Specificationsa
Center Wavelengthb 1550 nm ± 15 nm
Output Powerc >90 mW (Typ. 120 mW)
Linewidthd <250 Hz (Typ. 100 Hz)
Relative Intensity
Noise (RIN)e
-160 dBc/Hz
Side Mode Suppression
Ratio (SMSR)
>60 dB (Typ. 70 dB)
  • See Specs Tab for Full Specifications
  • If you require a specific wavelength, please contact Tech Support with inquiries.
  • Measured at the bulkhead.
  • Measured based on the Lorentzian definition. Please refer to the ULN15PC laser manual for details.
  • Represents the typical value at 10 MHz frequency.

Applications

  • Optical Reference Laser
  • LIDAR/LADAR
  • Fiber Optic Sensing

Features

  • Turnkey C-Band, Single-Frequency Laser System
  • Analog Modulation Inputs for DC Current, AC Current, and Laser Temperature
  • Temperature-Stabilized Laser Case for Long-Term Stability
  • Integrated Fiber Isolator with >25 dB Isolation to Minimize Effects of Back-Reflected Light
  • Remote Operation and Set-Point Adjustment with Command-Line Interface via USB 2.0
ULN15TK with PM Fiber and SMA Cables
Click to Enlarge

The ULN15TK laser can be mounted to an optical table using four 1/4"-20 cap screws. The ULN15TK is pictured with a P3-1550PM-FC-5 PM fiber patch cable and three CA2912 SMA cables, which are connected to the optical output and analog modulation ports, respectively.

Reza Salem
BU Leader, Fiber Lasers

Feedback?

Questions?

Need a Quote?

Contact Me

Thorlabs' ULN15TK Turnkey, Ultra-Low-Noise (ULN) Laser System is a ready-to-use laser system that integrates our ULN15PC laser, which has a patented fiber Bragg grating (FBG) based design, with a low-noise driver and temperature stabilization inside of a benchtop housing. This turnkey laser system provides single-frequency emission with relative intensity noise below -160 dBc/Hz and typical (Lorentzian) linewidths of 100 Hz. Factory-set for optimized performance, this laser offers typical optical output powers of 120 mW with a side mode suppression ratio (SMSR) of 70 dB.

The optical output of this laser is fiber-coupled via an FC/APC bulkhead (2.0 mm narrow key) output connector. For best performance, we recommend connecting our PM FC/APC fiber patch cables that contain PM1550-XP fiber, such as the P3-1550PM-FC-1 patch cable. Note that the polarization axis is aligned with the narrow key of the bulkhead connector.

The system is powered by a 12 VDC, 4 A input. A DS12 power supply is provided with each laser; see the Shipping List tab for a complete list of items included with the device.

Single-Frequency Operation
Factory-set for single-frequency operation, the ULN15TK laser has a preset drive current and FBG temperature. These operating conditions are selected to minimize the laser linewidth while also providing the highest output power and long-term stability.

To achieve the narrow linewidth of the ULN15PC laser, this turnkey ULN laser includes drive electronics that are designed to minimize the current noise. The drive electronics also includes a thermal stabilization system that controls the internal temperature settings of the laser and ensures long-term power and wavelength stability when the system is used in standard laboratory environments. A fiber isolator is also integrated at the output of the laser in order to minimize the impact of any back-reflected light on the laser.

When this turnkey laser is enabled using the push-button switch on the front panel (see Front & Back Panels tab), the laser operates at the preset current level. Each laser is shipped with a test data sheet taken at the preset operating conditions; click here for a sample data sheet. For typical frequency noise and relative noise intensity plots, see the Graphs tab. Please note that the laser requires a 10 minute warm-up after it has been enabled in order to reach its specified linewidth.

Analog Modulation
By controlling the laser drive current or temperature, the laser wavelength can be tuned free of mode-hopping within a small range around its set-point. Three analog modulation ports (SMA Female) are included on the front panel (see the Front & Back Panels tab). Two of the ports allow the laser current to be modulated by ±10 mA around the current set point: of these, the port labelled "AC Current" can support modulation frequencies up to 20 MHz, and the port labelled "DC Current" accepts frequencies from DC to 5 MHz. The third port, which is labelled "Temp", controls the FBG temperature and accepts modulation frequencies from DC to 1 Hz. To see how the laser wavelength can be tuned around its set-point, please see the wavelength tuning plots provided in the Graphs tab.

Each modulation port accepts a -5 V to 5 V input signal. To convert the modulation voltage into a current or temperature change, see the Specs tab.

Remote Operation
Remote operation is also possible by connecting the laser to a PC (not included) via the USB port on the back of the unit and using a command line interface. In addition to basic functions such as turning the laser on and off or reading status indicators, the command line enables the user to modify the laser operating set-points. A USB-AB-72 USB 2.0 Type-A to Mini-B Cable is included with each device.

Adjusting the laser parameters within a limited range around the set-point can be used to tune the center wavelength while staying in the single-frequency operating regime. If the setpoints are changed outside of this limited range of values, the lasing spectrum of the laser may change between single longitudinal mode and multimode; see the full ULN15PC web presentation for a detailed discussion on single-mode operation. Typical performance plots that demonstrate the laser's center wavelength tuning and the single-mode operating regions can be found on the Graphs tab. Please note that specific performance data is provided on the datasheet shipped with each device.

A 9-Pin female D-Sub connector is also included on the back panel of the system for RS-485 communication protocol. Please refer to the Pin Diagrams tab for the pin assignment of the connector.

Mounting
For mounting to an optical table, the compact housing of this benchtop ULN laser features four clearance holes each for M6 and 1/4-20" cap screws.

Item # ULN15TK
Laser Specificationsa
Center Wavelengthb 1550 nm ± 15 nm
Output Powerc >90 mW (Typ. 120 mW)
Linewidthd <250 Hz (Typ. 100 Hz)
Relative Intensity Noise (RIN)e -160 dBc/Hz
Side-Mode Suppression Ratio (SMSR) >60 dB (Typ. 70 dB)
Polarization Extinction Ratio (PER) >18 dB
Output Isolation >25 dB
Laser Class 1M
Fiber Specifications
Output Fiber Typef Corning® PM15-U25D
Output Fiber Connectors FC/APC Compatible,
2.0 mm Narrow Key
External Modulation Specifications
Voltage to Current Conversion Rate (AC and DC) 2 mA/V
Voltage to Temperature Conversion Rate Firmware Adjustable
(Default = 0.2 °C/V)
Input Voltage Range (All Ports) -5 V to 5 V
Input Impedance (All Ports) 1 kΩ
AC Current Modulation Frequency Rangeg 2 kHz to 20 MHz
DC Current Modulation Frequency Rangeg DC to 5 MHz
Temperature Modulation Frequency Range DC to 1 Hz
  • Taken at Factory Preset Operating Conditions
  • If you require a specific wavelength, please contact Tech Support with inquiries.
  • Measured at the bulkhead.
  • Measured based on the Lorentzian definition. Please refer to the ULN15PC laser manual for details.
  • Represents the typical value at 10 MHz frequency.
  • Compatible for mating with Thorlabs' PM1550-XP patch cables.
  • The specified bandwidth refers to the 3 dB electrical bandwidth of the modulation circuits. The laser response has a slow roll-off for frequencies above 1 MHz.
Absolute Maximum Ratings
Absolute Maximum Output Power 145 mW
Operating Temperature 15 °C to 30 °C
Storage Temperature -10 °C to 40 °C
General Specifications
Input Voltage 12 V (from DS12 Power Supply)
Input Power 20 W (Max)
Dimensions (W x D x H) 10.00" x 5.31" x 2.93"
(254.0 mm x 135.0 mm x 74.4 mm)
Weight 4.7 lbs (2.1 kg)

The plots below represent the typical performance of the ULN15TK ultra-low-noise laser system. Specific performance data is provided on the datasheet shipped with each device; click here for a sample data sheet.

ULN15TK Frequency Noise Spectral Density
Click to Enlarge

Click Here for Data
Example frequency noise data for a ULN15TK laser system operated at the factory-set conditions. Using the high-frequency white noise level estimation described in the ULN15PC manual, this ULN15TK laser has an approximate Lorentzian linewidth of 70 Hz.
ULN15TK Relative Intensity Noise
Click to Enlarge

Click Here for Data
The typical low-frequency relative intensity noise (RIN) for a ULN15TK laser system operated at the factory-set conditions.
ULN15TK Single Mode Operating Regions
Click to Enlarge

Click Here for Data
The typical single mode operating regions for a ULN15TK laser system operated at a Fiber Bragg Grating temperature (TFBG) of 27 °C. Multimode regions have been removed.
ULN15TK Center Wavelength Tuning
Click to Enlarge

Click Here for Data
The center wavelength (λc) tuning with changes in the pump current and Fiber Bragg Grating temperature (TFBG). Multimode regions have been removed.
ULN15TK Typical Spectrum
Click to Enlarge

Click Here for Data
The typical spectrum for a ULN15TK laser system operated at the factory-set conditions. This measurement is limited by the 0.02 nm optical spectrum analyzer resolution bandwidth.
ULN15TK Back Panel
Click to Enlarge

ULN15TK Turnkey ULN Laser Back Panel
ULN15TK Front Panel
Click to Enlarge

ULN15TK Turnkey ULN Laser Front Panel
Front Panel
Call Out Description
1 Status Indicator LEDs
2 Laser Output Port (FC/APC, PM Fiber Output)
3 Laser Enable Push-Button Switch
4 AC Current Modulation Input (SMA Female) 
5 DC Current Modulation Input (SMA Female)
6 Temperature Control Modulation Input (SMA Female)
Back Panel
Call Out Description
1 RS-485 Communication (DB-9 Female)
2 USB Communication (USB Mini-B)
3 Remote Interlock Pin (2.5 mm Mono Phono Female)
4 DC Input (M8 Connector for the DS12 Power Supply)

USB 2.0 Communication

USB Mini-B

Input for Analog Modulation

SMA Female

Input Voltage: -5 V to 5 V
Input Impedance: 1 kΩ
AC Current Modulation Frequency Range: 2 kHz to 20 MHz*
DC Current Modulation Frequency Range: DC to 10 MHz*

*The specified bandwidth refers to the 3 dB electrical bandwidth of the modulation circuits. The laser response has a slow roll-off for frequencies above 1 MHz.

RS-485 Communication

9-Pin Female D-Sub Connector

Pin Assignment
Pin Output Signal
1 RS-485 Half-Duplex T/R+
2 RS-485 Half-Duplex T/R-
3 Not Connected
4 Not Connected
5 Ground
6 Not Connected
7 Ground
8a Do Not Connect
9a Do Not Connect
  • These pins are for factory configuation use only.

The ULN15TK Turnkey Ultra-Low-Noise Laser System ships with the following components:

  • Ultra-Low-Noise Laser in Benchtop Housing
  • DS12 Power Supply
  • USB-AB-72 USB 2.0 Type-A to Mini-B Cable, 72" (1.83 m) Long
  • FBC250 Connector and Bulkhead Cleaner
ULN15TK Laser Stabilization Application
Click for Details

Experimental Setup for Laser Stabilization

Laser Stabilization

The ULN15TK turnkey ultra-low noise laser offers exceptional optical spectral purity and is configured for out-of-the-box use with little setup effort. However, for the most demanding applications, such as optical clocks and high-resolution spectroscopy, active electronic feedback may be required to further suppress technical noise and drifts. This turnkey laser conveniently provides multiple high-bandwidth analog modulation ports for locking to external optical references such as an optical cavity or an atomic/molecular transition.

Thorlabs offers low loss supermirrors on their own or integrated into custom reference cavities. In the figure to the right, we show an example of how the Pound-Drever-Hall (PDH) locking scheme is used to lock the ULN15TK laser to a reference cavity comprised of XM12R8 and XM12P8 crystalline supermirrors attached to an ultra-low expansion glass spacer. The RF modulation input conveniently permits the PDH sidebands to be generated without an external optical modulator. Demodulation of the reflected signal from the cavity yields an error signal which can be processed with a servo filter to maintain resonance with the optical cavity. This turnkey laser provides a high-bandwidth DC-coupled current modulation port to correct for fast fluctuations, and a slower temperature modulation port with larger range to correct for slower drifts.


Posted Comments:
Oliver Dölle  (posted 2023-04-03 14:53:43.483)
Hi, we will integrate the ULN15TK in our Laser stabilization system. Therefore I need the dimensions of the ULN15TK. Can you send me any technical drawings? Perhaps you have even a CAD model (step or iges)? That would help me a lot! Thank you, Oliver Dölle, zeptocision GmbH
cdolbashian  (posted 2023-04-03 02:47:49.0)
Thank you for reaching out to us Oliver! These types of information can be found by clicking the red-colored "Docs" icon to the left of each product part number within the overview tab above.
Back to Top

Turnkey Ultra-Low-Noise Laser System

Based on your currency / country selection, your order will ship from Newton, New Jersey  
+1 Qty Docs Part Number - Universal Price Available
ULN15TK Support Documentation
ULN15TKTurnkey Ultra-Low-Noise Laser System, 1550 nm, 120 mW, PM Fiber, FC/APC
$13,387.50
Today